The Fundamentals of Plumbing Knowledge for Bathtub Installation
The Fundamentals of Plumbing Knowledge for Bathtub Installation
Blog Article
How do you really feel on the subject of A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't exactly brain surgery, but it does require solid plumbing, carpentry, and also often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a moderately tough task. If the old tub is readily easily accessible, the project can move rapidly; if you need to open up a wall surface to get rid of the old tub and position the new bath tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the brand-new one. Make sure you have certified on your own for the job and fit trying it. Rather than employing a service provider to take control of a halfway-completed project, it is better to think about utilizing one before you begin. Chances are you might require a professional plumber to make tube connections.
This article will certainly assist you mount a brand-new bath tub in your restroom if you have already gotten a brand-new tub and also don't need to alter the plan of your previous water pipelines.
Your devices as well as material checklist must comprise the following:
Preparing for the Installment
To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets unit to stop pressure on the tub.
Fit the adaptable tap ports to the bottom of the two taps making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any water remaining in the system. The process of removing the existing faucets can be rather troublesome due to the limited access that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a fabric prepared for the remaining water that will originate from the pipelines. Once the supply pipelines have been gotten rid of, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before proceeding to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Making use of both wooden boards under its feet, position the bath tub in the needed position. The wooden boards are valuable in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four little factors.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by checking the level as well as readjusting the feet on the bathtub until the spirit level checks out level.
To install taps, fit all-time low of the furthest versatile faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the water and inspect all joints as well as brand-new pipework for leakages and also tighten them if required. Fill up the bathtub and likewise inspect the overflow outlet and the regular electrical outlet for leaks.
Lastly, fix the bathroom paneling as explained in the maker's instruction manual. Tiling as well as sealing around the tub should wait up until the bathtub has actually been used a minimum of when as this will certainly resolve it right into its last setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former type needs to be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture a stiff seal, causing the water to pass through the wall in between the bath and the tiling, resulting in problems with dampness and feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components as well as installations. They are offered in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealant can split rather early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or water-proof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that article on How to Install a Bathtub through someone on another site. Sharing is caring. Helping people is fun. Thanks for going through it.
24/7 plumbers for emergencies. Report this page